Gear Reduction Starter @ JC Whitney Auto Parts store
Gear Reduction Starter
PERFORMANCE GEAR REDUCTION STARTER Ends all hot start problems�forever! One year manufacturer warranty Get total starting power! Far superior to original equipment. 100% more torque�4.4:1 gear reduction, roller bearing support and integrated solenoid ensure this starter can crank any engine, no matter how high its static compression. 200% more cranking power. More starts�20,000 starts vs. 5,000 for stock. Uses less amperage. Turns faster under load, slower under no load and is more cold-weather resistant. Enhanced rock/hill climbing ability with clutch-free starting. 1/3 smaller size and weight for easy installation. Heavy-duty construction and extreme reliability are the primary hallmarks of this performance gear reduction starter. Five sealed ball bearings increase efficiency, reduce wear and thrive under extreme conditions, like water intrusion. Integral solenoid is corrosionproof and heat-sinked to prevent overheating and thermal breakdown. Stainless steel mainshaft provides direct line engagement, which increases even further efficiency, power and reliability. Also, the rotating billeted aluminum nose cone adapter can be turned in 20� increments (depending on application) to clear headers, oil pans or other obstacles. Depending on application there are dual-bolt patterns so they fit both the 153-tooth and 168-tooth flywheels. PSI certified and approved. All applications are for gas engines except where noted. Applications: Ford All Models 8-cyl small block 289; 302; 351W with automatic transmission SKU: 81ZX5815Y
Glass Sunroof
GLASS SUNROOFS Sunlight-filtering High Performance� glass blocks 92% of UV rays 2-position original-equipment-style latch for ventilation Removes easily for open-air riding Sleek, contemporary styling for that factory-installed look. Narrow precontoured black aluminum frame conforms to vehicle and fits perfectly. Deep, smoke colored glass (darker than OEM glass) provides excellent light and solar transmission resistance to keep interior cooler. Flush, tempered glass is sealed with waterproof, leakproof 100% silicone seal. Template, mounting hardware and instructions included. For all American and Imported cars, trucks and vans (except vans with ridged roof, Volkswagen Beetle, Corvette, Pontiac Fiero, 1992-2001 Pontiac Grand Am, Oldsmobile Achieva, Buick Skylark, 1993-2001 Camaro, Firebird & Trans Am). Shipped separately from factory. NOTE: SKU numbers ending in F are factory shipped and may take a little longer to reach you. Applications: All Makes All Models, All Makes All Models SKU: 78ZX7651PF
HEAVY-DUTY RUBBER BED MAT WITH LOGO Priced-right protection for your full-size pickup's bed with a custom flair! You can depend on this workhorse not only to prevent mars, scratches and dents but also to prevent your cargo from sliding around! Licensed logo in the center makes a powerful styling statement Slips easily into place. Simply hose off to clean. Will not fit Stepside models. LB=Long Bed. SB=Short Bed. Chevy Bow Tie� is a trademark of General Motors Corp. Ford Oval logo is a trademark of Ford Motor Company. Dodge Ram Logo is a trademark of Daimler Chrysler Corp. Applications:1994-2001 Dodge Pickup - Full Size LB SKU: 48ZX8052X
GENERIC/RV, MOTOR HOMES, OUTDOOR/JACKS & LEVELERS
TELESCOPING STABILIZERS Strong steel unit bolts or welds to vehicle's frame�easier to install than T-type stabilizers. Opens and closes easily with speed crank included. Set includes 2 stabilizers, hardware. Stabilizers sold by height (distance between frame and ground). 8"-long drive screw extension. 2,000-lb. static load per leg. Fit 61"- to 74"-wide frames. Order 2 sets to stabilize both front and rear. Cannot be shipped express. 2 sizes: one adjusts from 3-1/2" to 18" high, 20"-long leg; the other adjusts from 3-1/2" to 21" high, 24"-long leg. Base pads (7" diam.) for firm footing on soft ground available, sold separately. Applications: All Makes All Models SKU: 20ZX0885P
